Staub-electronics SM-CS-ART2-L STRONG - CONTRACTOR SERIES ARTICULATI User Manual download pdf

Step 4 : Mounting the Assembled Adapter

Plate to Screen

Modify the Assembled Adapter Plate

Slide the Adapter Brackets onto Assembled Adapter

Plate rods. Place the assembled Adapter Plate on the

back of the display with one Adapter Bracket aligned

with a set of vertical mounting holes. Then, slide the

other Adapter Bracket in or out until it aligns with the

second set of vertical mounting holes. The Adapter Plate

should be horizontally centered on the back of the at

panel display.

Use four M6x12 screws and four metal washers and tighten

Adapter Brackets to Adapter Plate rods with a Phillips Head

Screw Driver.

NOTE: There are eight positions for exibility. Move

the Adapter Brackets to desired location. Adapter

Brackets can be ipped around (if required).

Attach the Adapter Brackets using four mounting screws

and four square washers (size will depend on thread pat-

tern on at panel being installed). Once aligned, tighten

all screws down with a Phillips Head Screw Driver.

Insert two M8 Hex head screws on the top of the Adapter

Plate with the M6 Allen Wrench. DO NOT IMMEDIATELY

TIGHTEN DOWN!

Step 5: Attaching Screen to Wall Arm Assembly

Lift the display and hook the two Hex head screws with

metal washers in grooves on top of the Mounting Head.

Insert two more Hex head screws with washers in bot-

tom two holes of the Mounting Head, securing it to the

Adapter Plate. Then tighten all four screws with the

Allen Wrench.

NOTE: For demonstration purposes, the wall has been

omitted from the illustrations.

NOTE: This procedure will require two persons.

Ensure that the arm is set to its maximum negative

tilt prior to attaching the display.

Step 6: Running Cables

Run as shown and install Wire Management Caps.

NOTE: Make sure cords have enough slack to allow

full movement of the arm.

Mounting

Head

Tilt Levers

M8 Hex head

screws w/washers

Adapter

Plate

Back of

Display

Adapter

Bracket

Metal Washer

(6 x 13 x 1.2)

M6 x 12

Screw

Mounting

Screw

Square

Washer

M8 Hex head

screws w/washers

Wire Management

Caps

SM-CS-ART2-L

Strong™ Contractor Series Universal

Articulating Mount With Dual Arms

For Large Displays

INSTRUCTION MANUAL

Lifetime Limited Warranty

Strong™ Mounts have a Lifetime Limited Warranty. This warranty

includes parts and labor repairs on all components found to be

defective in material or workmanship under normal conditions of

use. This warranty shall not apply to products which have been

abused, modied or disassembled. Products to be repaired under

this warranty must be returned to Snap AV or a designated service

center with prior notication and an assigned return authorization

number (RA).

For customer assistance call 1.866.838.5052

Lifetime

1 2

Summary of Contents

Page 1 - INSTRUCTION MANUAL

Step 4 : Mounting the Assembled Adapter Plate to ScreenModify the Assembled Adapter PlateSlide the Adapter Brackets onto Assembled Adapter Plate rod

Page 2 - ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONSWARNINGS:• Make sure these instructions are read and thoroughly understood before attempting installation. If you are unsure of

Comments to this Manuals

No comments

Staub-electronics SM-CS-ART2-L STRONG - CONTRACTOR SERIES ARTICULATI User Manual

Browse online or download User Manual for Accessories for video Staub-electronics SM-CS-ART2-L STRONG - CONTRACTOR SERIES ARTICULATI. Staub Electronics SM-CS-ART2-L STRONG - CONTRACTOR SERIES ARTICULATING MOUNT FOR 42 - 63 FLAT PANEL TVS User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for video Staub-electronics SM-CS-ART2-L STRONG - CONTRACTOR SERIES ARTICULATI